[. . . ] SyncMaster P64FP P64FT PDP Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Note Important to read and understand at all times Disconnect the plug from the outlet Ground to prevent an electric shock Prohibited Do not disassemble Do not touch An administration fee may be charged if either · (a) an engineer is called out at your request and there is no defect in the product (i. e. [. . . ] Mute will automatically be disabled if Volume is adjusted when Mute is on. 3 z Alert Fault Device This menu shows a list of display devices which have following errors - fan error, temperature error, brightness sensor error, or lamp error. Click the refresh button to refresh the error status of the display device. The recovered display device will disappear from the Fault Device List. Fault Device Alert Display device in which error is detected will be reported by email. Ensure the Sender information and at least one Recipient are entered. Screen Adjustment The screen settings (contrast, brightness, etc. ) can be adjusted. Choose display devices from the list of sets, and select the Picture tab. Custom Select an item and change the corresponding screen setting. z z z Color and Tint are not available if the input source is PC. Red, Green, Blue and PC Screen Adjustment are not available if the input source is Video. Color, Tint, Color Tone, Color Temp, Red, Green, Blue and PC Screen Adjustment are not available if both PC Source and Video Source are selected. Contrast z Adjust the contrast for the selected display device. Brightness z Adjust the brightness for the selected display device. Color z Adjust the colors for the selected display device. Tint (G/R) z Adjust the tint for the selected display device. Color Tone z Adjust the background color tone for the selected display device. Color Temp z Adjust the color temperature for the selected display device. This option is enabled if Color Tone is set to Off. Red z Customize the intensity of red color for the selected display device. Green z Customize the intensity of green color for the selected display device. Blue z Customize the intensity of blue color for the selected display device. Options Dynamic Contrast Adjust the Dynamic Contrast for the selected display device. Auto Motion Plus This option is used to view dynamic images. z Off: Disable the Auto Motion Plus function. The result when the mode is changed can be previewed on the left side of the window. z z z z z Brightness Sensor Enable or disable the Brightness Sensor for the selected display device. The Brightness Sensor detects the ambient light intensity and automatically adjusts the screen brightness. Brightness Sensor may not be available depending on the product. Size Picture Size Adjust the screen size for the selected display device. The Detail item will be disabled if Picture Size is set to a mode that does not support detailed configuration. PC Screen Adjustment Frequency adjustment or fine-tuning is available by using the -/+ buttons in Coarse or Fine. To automatically adjust the frequency, fine-tune or relocate the screen, click Auto Adjustment. Sound Adjustment You can change the sound settings. Choose display devices from the list of sets, and select the Sound tab. The Bass or Treble item will be disabled if the item is not supported by the selected set. Bass Adjust the bass for the selected display. Treble Adjust the treble for the selected display. Balance (L/R) Adjust the volume of the left and right speakers of the selected display device. SRS TS XT Enable or disable the SRS TS XT effect for the selected display device. System Setup Choose display devices from the list of sets, and select the System tab. Video Wall The Video Wall function can be used to display part of a whole picture or repeat the same picture on each of connected multiple display devices. Video Wall is enabled only when devices are in the group. Video Wall Enable or disable Video Wall. Format Select the format to display the split screen. H Select the number of horizontal display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. V Select the number of vertical display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. Screen Position View the layout of displays (configured by the screen divider) or change the layout as required. Note that if multiple sets are selected, Preview is enabled only if the settings for H and V match the layout of the selected sets. To change the Position, select a set and drag it to a new position. The range of screen divider settings may differ depending on the model. PIP Basic information required to adjust PIP will appear in the menu screen. z z PIP will be disabled when Video Wall is ON. Note that Picture Size is disabled when PIP is ON. PIP Size View the PIP Size of the current display. Sound Select Select and enable the sound from either the primary screen or secondary screen. Channel The channel can be changed if PIP Source is TV. General User Auto Color Automatically adjust the screen colors. Available only in PC mode. Auto Power Set the product to automatically power on. [. . . ] Unit: kHz Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. [. . . ]